Update to Automatic Bandwidth Adjustment procedure of Stateful PCE

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶

This Internet-Draft will expire on 4 January 2024.¶

Copyright Notice

Copyright (c) 2023 IETF Trust and the persons identified as the document authors. All rights reserved.¶

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶

Table of Contents

1. Introduction

[RFC5440] describes the Path Computation Element Communication Protocol (PCEP). PCEP defines the communication between a Path Computation Client (PCC) and a Path Computation Element (PCE), or between PCEs, enabling computation of Multiprotocol Label Switching (MPLS) for Traffic Engineering Label Switched Path (TE LSP) characteristics.¶

[RFC8231] specifies extensions to PCEP to enable stateful control of MPLS TE LSPs. It describes two modes of operations - Passive stateful PCE and Active stateful PCE. Further, [RFC8281] describes the setup, maintenance and teardown of PCE-Initiated LSPs for the stateful PCE model.¶

[RFC8733] describes the auto-bandwidth feature that allows automatic and dynamic adjustment of the TE LSP bandwidth reservation based on the volume of traffic flowing through the LSP. It describes PCEP extensions for auto-bandwidth adjustment when employing an active stateful PCE for both PCE-initiated [RFC8281] and PCC-initiated LSPs. It defines the AUTO-BANDWIDTH-ATTRIBUTES TLV that provides the 'configurable knobs' of the feature, and it can be included as an optional TLV in the LSPA object. The TLV is encoded in all PCEP messages for the LSP while the auto-bandwidth adjustment feature is enabled. The absence of the TLV indicates the PCEP speaker wishes to disable the feature. The TLV includes multiple AUTO-BANDWIDTH-ATTRIBUTES sub-TLVs defined in [RFC8733]. The AUTO-BANDWIDTH-ATTRIBUTES sub-TLVs are included if there is a change since the last information sent in the PCEP message. It also states that in the case of a missing sub-TLV, as per the local policy, either the default value or some other operator-configured value is used.¶

Since the missing sub-TLV in a subsequent PCEP message is considered as no change, there is no mechanism to remove a particular attribute encoded in the sub-TLV. This document updates [RFC8733] to define such a procedure.¶

Note that for the attributes that have an associated default value, they could simply encode the default value in the sub-TLV but this cannot be used for the attributes that do not have a default value.¶

This document proposes to use a special value of all zeros to indicate "restore to default", which could mean going back to the default values or removal of the attribute itself.¶

The following table includes the sub-TLVs and the default values as per [RFC8733].¶

Thus, the use of the special value of all zeros in the value portion of the sub-TLV can be used to indicate "restore to default", which could mean :¶

• if the default value is set for the sub-TLV:¶

  • Restore to the default values¶

• if there is no default value for the sub-TLV:¶

  • Remove the associated attribute¶

2. Conventions

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶

3. Updated Procedures

Section 5.2 of [RFC8733] defines the AUTO-BANDWIDTH-ATTRIBUTES TLV and its associated sub-TLVs.¶

This document updates [RFC8733] by adding this text at the end of paragraph 3 in section 5.2:¶

A special value of all zeros in the value portion of the sub-TLV
indicates the attribute identified by the sub-TLV is restored to
the default value. The value of all zeros is not considered an
invalid value and MUST be checked before individual fields.

For the attributes that have an associated default value, on
receiving such a sub-TLV, the PCEP speaker MUST consider it as
an instruction to restore to the default values. Note that, the
PCEP speaker could also set the default value in the sub-TLV
itself.

For the attributes that do not have an associated default value,
on receiving such a sub-TLV, the PCEP speaker MUST consider it
as a removal of the specific auto-bandwidth attribute.

4. Extensions

The section 5.1.1 of [RFC8733] defines the AUTO-BANDWIDTH-CAPABILITY TLV as an optional TLV for use in the OPEN Object for auto-bandwidth adjustment. This document adds a new flag -¶

Z (TBD): The flag indicates that a PCEP speaker supports the use of the special value of all zeros in the value field as specified in this document.¶

The presence of the Z flag can give a clear indication to the PCEP peer if they can use the updated procedures defined in this document.¶

5. Example

Consider an LSP with the following information in the AUTO-BANDWIDTH-ATTRIBUTES TLV in the PCInitiate message:¶

• Sample-Interval: 600 (in sec)¶
• Adjustment-Interval: 172800 (2 days in sec)¶
• Adjustment-Threshold: 0x49989680 (10 mbps in bps)¶

Now if the PCE would like to not use the Adjustment-Thresholds feature for the LSP and set the Adjustment-Interval to 1 day, it could send the AUTO-BANDWIDTH-ATTRIBUTES TLV in the PCUpd message with the following sub-TLVs:¶

• Adjustment-Interval: 86400 (1 day in sec, the default value)¶
• Adjustment-Threshold: 0x0¶

On receiving the special value of all zeros in the value portion of the Adjustment-Threshold sub-TLV, the PCEP speaker would consider that as removal of the Adjustment-Threshold feature.¶

Note that, the PCE could also set the Adjustment-Interval: 0x0 instead of the default value to trigger the restore to default. The Sample-Interval remains unchanged.¶

6. Backward Compatibility

Note that to achieve the same objective, an [RFC8733] compliant implementation could send a PCEP message without AUTO-BANDWIDTH-ATTRIBUTES TLV first and then include the AUTO-BANDWIDTH-ATTRIBUTES TLV with the updated sub-TLV.¶

An existing implementation of [RFC8733] that does not support this update (Z flag is not set) could consider a special value of all zeros in the sub-TLV to be a malformed sub-TLV thus ignoring it and keeping the previous value. A PCEP speaker SHOULD use other techniques in this case.¶

7. Security Considerations

TBD¶

8. IANA Considerations

Appendix A. Acknowledgments

TBD¶

Authors' Addresses